Press F1 to exit from this helpfile, and use cursor up and down to scroll.

To quit the program press Ctrl-Q (but exit this helpfile first).

______________________________________________________________________________

The keyboard operates as follows:

(Note Alt-P has changed its meaning in release 0.97: to send FEC
Pactor in Tor mode, now press Alt-T)

Cursor up - Scroll up.
Cursor down - Scroll down.
Cursor right - Scroll out (end scroll).

Page Up - changeover to transmit (HF modes).
Page Down - changeover to receive (HF modes).

Note: if using xterm, you may need to use the Page Up and Page Down on
the number pad to make this work, rather than the Page up and Page
Down on the main keyboard.

Ctrl-A: change to Amtor mode (or send Ctrl-A - see below).
Ctrl-C: change to CW mode (if not in CW mode) or set the speed (if in CW
	mode).
Ctrl-D: disconnect (Packet, Pactor, Amtor and Gtor).
Ctrl-F: change to FEC.
Ctrl-G: change to G-tor.
Ctrl-L: change to Lamtor.
Ctrl-O: change to Gmon.
Ctrl-P: change to Pactor.
Ctrl-Q: quit the program.
Ctrl-R: change to RTTY (Baudot).
Ctrl-S: change to ASCII.
Ctrl-T: change to TOR mode (or send Ctrl-T - see below).
Ctrl-X: change to HF Packet.
Ctrl-Z: send Ctrl-Z (see below).

Alt-B: print the current scroll buffer.
Alt-C: send an auto-cq (Pactor, Amtor, Gtor or Tor-Standby)
       or (if in auto-cq mode) end auto-cq
       (see also Alt-T below).
Alt-D: Download a 7plus/uuencoded file to a local file (Packet, Pactor
       or Gtor) (this makes no translations other than CR -> LF).
       (Press again to end the download).
Ctrl- Alt-D: Download a binary file to a local file (Packet, Pactor or
       Gtor) (this saves the raw data to disk).
       (Press again to end the download).
Alt-I: send ident ([CALL IN STORE] de [YOUR CALL]).
Alt-L: toggle whether receive speed locked to 100 baud (Pactor or Gtor).
Alt-P: set a print mark, or if one is already set, print from the mark.
Alt-R: enter an RST report to be stored in the RST buffer.
Alt-S: sync the transmit speed to the current receive speed (CW), or
       resync the Amtor decoder when monitoring (Amtor/Lamtor).
Alt-T: send an auto-cq when listening in Tor-standby mode but using
       Pactor FEC to send the CQ.
Alt-U: Upload a 7plus/uuencoded file (Packet, Pactor or Gtor) (this
       makes no translations other than LF -> CR).
       (Press again to abort the upload).
Ctrl-Alt-U: Upload a binary file (Packet, Pactor or Gtor) (this
       sends raw data and makes no translations).
       (Press again to abort the upload).
Alt-X: abort (Pactor, Amtor, Gtor or Tor)
Alt-0 to Alt-9: send the messages specified in the "messages" file.

F1: toggle display of Help file (press it again to return to main display).
F2: toggle on/off capture of current stream to file [KAMDIR:]/capture.txt.  
F3: toggle transmitting of text after word/line in non-packet mode or with
    a guard in non-packet mode.  
F4: connect with another station (Packet, Pactor, Amtor and Gtor).  
F5: send a command to the Kam (press again to run a configuration script).
F6: send a text file. (Press again to abort the upload).
F7: enter another station's callsign in the callsign store.  
F8: toggle the callsign lock.  
F9: send the Kam parameter file tnc.parms to Kam.  
F10: toggle the screen display between VHF and HF port of Kam.  
F11: go down a stream on the screen display (e.g. from stream C on current
     port to stream B).  
F12: go up a stream on the screen display (e.g. from stream A on current
     port to stream B).

Pressing Ctrl-A when in Packet, Pactor or Gtor mode and connected
will send a Ctrl-A character instead of asking whether to change to
Amtor mode (some BBSs use Ctrl-A to abort a message being sent)

Pressing Ctrl-T when in Packet, Pactor or Gtor mode and connected
will send a Ctrl-T character instead of asking whether to change to
Tor mode (some BBSs use Ctrl-T to abort a telnet session)

Pressing Ctrl-Z when in Packet, Pactor or Gtor mode and connected
will send a Ctrl-Z character (some BBSs use Ctrl-Z to end a message as
an alternative to /EX)

If Alt-C is pressed when in Pactor, Amtor, Gtor or Tor-Standby modes,
the program will run the CQ message found in the file 'cq' placed in
the directory specified by 'KAMDIR:' in kamrc, repeating until a link
is made.  It can be turned off by pressing Alt-C again.  The delay
between the end of one CQ message and the start of the next may be
specified by the AUTOCQ: parameter in kamrc.  If none is specified,
the default is 90 seconds (don't cook your output stage).  If in
Tor-Standby mode, pressing Alt-P will do the same, except that the CQ
message will be sent in Pactor FEC not Amtor FEC mode.

If Alt-L is pressed when in Pactor or Gtor mode, the receive speed
will be locked to 100 baud, and the bottom status line will show
"LOCK".

If Alt-1 to Alt-5 are pressed, the message specified in the file
"messages" will be sent ("messages" will be looked for in the
directory specified by KAMDIR: in kamrc).  If Alt-6 to Alt-0 are
pressed, the file specified in the "messages" file will be sent.  See
the specimen "messages" file installed by "make install" for further
details, including details of the shortcut macros that can be included
in a message.


Press F1 to exit from this helpfile.
